CryptoGPUs
Special orderShips in 2–5 days

Bitaxe Gamma 602

$73.15

Paid in Bitcoin, Monero, USDT or another coin you choose.

Insured shipping $29, free over $999. US delivery in about 5 to 11 business days. Shipping details

The minimum order is $399. Combine this with other products to reach it.

Overview

The Bitaxe Gamma 602 is a small open-source Bitcoin miner built around a single Bitmain BM1370 chip, the same silicon found in the Antminer S21 Pro. At stock settings it produces about 1.2 TH/s for roughly 15 to 20W, which works out to around 15 to 17 J/TH, and it runs from a plain 5V barrel-jack supply.

An ESP32-S3 controller runs the open-source ESP-Miner firmware, so the board mines over 2.4GHz Wi-Fi without a computer attached. You set the pool, frequency and voltage from the AxeOS web dashboard, and a 0.91 inch OLED shows hashrate and temperature. It accepts any Stratum pool or a solo pool, and it pairs well with your own node. The hardware design is CERN-OHL-S-2.0 and the firmware is GPL-3.0, but the BM1370 chip itself is closed.

Be realistic about income. Against a network of roughly 1 ZH/s, a single 1.2 TH/s device would be expected to find a block about once every 15,000 years, so solo mining here is a lottery ticket with a very small power bill. The board also needs active cooling and a supply rated for 25 to 30W.

Specifications

Mining performance
ASIC1 x Bitmain BM1370 (Antminer S21 Pro chip)
HashrateAbout 1.2 TH/s at stock settings
Power drawAbout 15 to 20W at stock; higher when overclocked
EfficiencyAbout 15 to 17 J/TH
Pool supportStratum V1 and V2; any pool, lottery or solo mining
Power and cooling
Power input5V DC, 5.5 x 2.1mm center-positive barrel jack
Supply requirement5V only, over 4A under load; 25 to 30W rated supply recommended
Cooling40mm 5V PWM fan with heatsink; active cooling required
Connectivity and control
ControllerESP32-S3
Wi-Fi2.4GHz
DisplayRemovable 0.91 in SSD1306 OLED
USBUSB-C for flashing and debugging
Software and licensing
FirmwareESP-Miner with AxeOS web dashboard (GPL-3.0)
Hardware licenseCERN-OHL-S-2.0; the BM1370 chip is not open source

Questions and answers

Still unsure? Visit the help center or message us.

Can a Bitaxe Gamma realistically solo mine a block?

Technically yes, practically no. With about 1.2 TH/s against a network hashrate near 1 ZH/s, the expected time to find one block is on the order of 15,000 years. Treat it as a hobby, learning and decentralization device, not income.

What does it cost to run?

At 15 to 20W it uses roughly 11 to 14kWh a month, which is about $1.50 a month at 12 cents per kWh. Overclocking raises both hashrate and power.

What power supply does it need?

A 5V DC supply with a 5.5 x 2.1mm center-positive barrel plug, delivering more than 4A without sagging below 5V. The project recommends a 25 to 30W unit, and a higher-voltage supply will damage the board.

Does it need a computer or a node?

No. The onboard ESP32-S3 connects over Wi-Fi and mines to any Stratum pool you configure in AxeOS. You can point it at your own node and solo pool for a self-run setup, but it is optional.

Is it really open source?

The PCB design files are published under CERN-OHL-S-2.0 and the ESP-Miner firmware under GPL-3.0. The Bitmain BM1370 ASIC is proprietary and not open source.

From the blog

All articles
Mining and nodes

Solo bitcoin mining at home in 2026: what a Bitaxe can really do

At October 2026 difficulty a 1.2 TH/s Bitaxe has about a 1 in 15,000 yearly shot at a block. The odds, power costs and pools for three home miners, worked out.

Pairs well with

Picked to go with this product. Check sizes and connectors for your build before you order.